10BaseT 10BaseF 10Base2 5-4-3 rule 10Base5 100BaseFX 100BaseT4 100BaseTX

 

IEEE shorthand identifiers, such as 10Base5, 10Base2, 10BaseT, and 10BaseF include three pieces of information:

·         The number 10: At the front of each identifier, 10 denotes the standard data transfer speed over these media - ten megabits per second (10Mbps).

·         The word Base: Short for Baseband, this part of the identifier signifies a type of network that uses only one carrier frequency for signaling and requires all network stations to share its use.

·         The segment type or segment length: This part of the identifier can be a digit or a letter:

·         Digit - shorthand for how long (in meters) a cable segment may be before attenuation sets in. For example, a 10Base5 segment can be no more than 500 meters long.

·         Letter - identifies a specific physical type of cable. For example, the

·         T at the end of 10BaseT stands for twisted-pair.

10BaseT

One of the most common types of Ethernet in use today is 10BaseT. This particular implementation uses four-pair UTP wiring (Cat3 or higher, but most commonly you will see Cat5) using RJ-45 connectors. Each cable is connected from each network device to a central hub in a physical star topology. Within the hub, the signals are repeated and forwarded to all other nodes on the network because it is a logical bus topology. Older network interface cards are configured with jumpers to set addresses and interrupts.

Today's network interface cards can be managed through a diagnostic program, or automatically configure themselves through plug and play technology. There is a limit of 1024 devices on an Ethernet segment, plus you can have a maximum of 1024 network segments. A UTP cable has a maximum distance of 100 meters, which is equivalent to 328 feet.

10BaseF

10BaseF is an implementation of Ethernet 802.3 over fiber optic cabling. 10BaseF offers only 10 Mbps, even though the fiber optic media has the capacity for much faster data rates. One of the implementations of 10BaseF is to connect two hubs as well as connecting hubs to workstations. The best time to use 10BaseF is in the rewiring of a network from copper to fiber optic, when you need an intermediate protocol using the new wiring. 10BaseF is not often a permanent solution because the data rate is so low and the cabling so expensive in comparison to using UTP.

10Base2

10Base2, also called ThinNet, is one of the two Ethernet specifications that use coaxial cable. (One of the best ways to remember that 10Base2 is ThinNet, and 2 is smaller than 10Base5, which is ThickNet.) One of the most important issues to remember in an Ethernet coax wiring scheme is the 5-4-3 rule,

5-4-3 rule
which states that you can have up to five cable segments, connected by four repeaters, with no more than three of these segments being mixing segments. In the days of coaxial cable networks, this meant that you could have up to three mixing segments of 500 or 185 meters each (for 10Base5 and 10Base2, respectively) populated with multiple computers and connected by two repeaters. You could also add two additional repeaters to extend the network with another two cable segments of 500 or 185 meters each, as long as these were link segments connected directly to the next repeater in line, with no intervening computers,

A 10Base2 network could therefore span up to 925 meters and a 10Base5 network up to 2,500 meters which states that there can only be 5 segments in a series and 4 repeaters between these 5 segments, although only 3 of the segments can be populated with devices. 10Base2 uses BNC connectors and is implemented as both a physical and logical bus topology using RG-58 cabling.

The minimum distance for cables between workstations must be at least a half-meter. Drop cables should not be used to connect a BNC connector to the network interface card (NIC) because this will cause signaling problems unless the NIC is terminated. 10Base2 ThinNet segments cannot be longer than 185 meters, although it is often exaggerated to 200 meters, and you can't put more than 30 devices on each populated segment. The entire cabling scheme, including all five segments, can't be longer than 925 meters.

10Base5

10Base5 is nearly identical to 10Base2, except that it uses a different type of cabling and media connector. 10Base5 is known as ThickNet because it uses the RG-8 coaxial cable. It requires an external transceiver to attach to the network interface card on each device. The transceiver is a device that translates the workstation's digital signal to a baseband cabling format. ThinNet and UTP network interface cards have built-in transceivers. Only 10Base5 ThickNet network interfaces use external transceivers. In the 10Base5 configuration, the NIC attaches to the external transceiver using an AUI connector. The transceiver then clamps into the ThickNet cabling, which is why it is usually called a vampire tap. 10Base5 can also use BNC connectors. For 10Base5, the following rules apply: First the 5-4-3 rule applies to ThickNet just as it did to ThinNet. In addition, the minimum cable distance between each transceiver is 2.5 meters. The maximum network segment length is 500 meters, which is where 10Base5 gets the "5" in its name. The entire set of five segments cannot exceed 2,500 meters. You can have 100 devices on a 10Base5 network segment.

100BaseFX

100BaseFX is simply Fast Ethernet over fiber. Originally, the specification was known as 100Base-X over CDDI (Copper Data Digital Interface) or FDDI (Fiber Data Digital Interface). Because the signaling is so vastly different, these two technologies were split into 100BaseFX and 100BaseTX. 100BaseFX runs over multimode fiber. There are two types of fiber in use. Multimode fiber optic cables use LEDs to transmit data and are thick enough that the light signals bounce off the walls of the fiber. The dispersion of the signal limits the length of multimode fiber. Single mode fiber optic cables use injected lasers to transmit the data along fiber optic cable with an extremely small diameter. Because the laser signal can travel straight without bouncing and dispersing, the signal can travel much farther than multimode.

100BaseT4

100BaseT4 was the specification created to upgrade 10BaseT networks over Cat3 wiring to 100 Mbps without having to replace the wiring. Using four pairs of twisted pair wiring, two of the four pairs are configured for half-duplex transmission (data can move in only one direction at a time). The other two pairs are configured as simplex transmission, which means data moves only in one direction on a pair all the time.

100BaseTX

100BaseTX, Fast Ethernet, transmits data at 100 Mbps. Leveraging the existing IEEE 802.3u standard rules, Fast Ethernet works nearly identically to 10BaseT, including that it has a physical star topology using a logical bus. 100BaseTX requires Cat5 UTP.

Gigabit Ethernet

The fastest form of Ethernet is currently Gigabit Ethernet, also known as 1000BaseT over Cat5 or highergrade cable, using all four pairs of the cable. It uses a physical star topology with logical bus. There is also 1000BaseF, which runs over multimode fiber optic cabling. Data transmission is full-duplex, but half-duplex is also supported.

1.3 Specify the characteristics (For example: speed, length, topology, and cable type) of the following cable standards:

·         10BASE-T and 10BASE-FL

·         100BASE-TX and 100BASE-FX

·         1000BASE-T, 1000BASE-CX, 1000BASE-SX and 1000BASE-LX

·         10 GBASE-SR, 10 GBASE-LR and 10 GBASE-ER

Designation	Supported Media	Maximum Segment Length	Transfer Speed	Topology
10Base-5	Coaxial	500m	10Mbps	Bus
10Base-2	ThinCoaxial (RG-58 A/U)	185m	10Mbps	Bus
10Base-T	Category3 or above unshielded twisted-pair (UTP)	100m	10Mbps	Star,using either simple repeater hubs or Ethernet switches
1Base-5	Category3 UTP, or above	100m	1Mbps	Star,using simple repeater hubs
10Broad-36	Coaxial(RG-58 A/U CATV type)	3600m	10Mbps	Bus(often only point-to-point)
10Base-FL	Fiber-optic- two strands of multimode 62.5/125 fiber	2000m (full-duplex)	10Mbps	Star(often only point-to-point)
100Base-TX	Category5 UTP	100m	100Mbps	Star,using either simple repeater hubs or Ethernet switches
100Base-FX	Fiber-optic- two strands of multimode 62.5/125 fiber	412 meters (Half-Duplex) 2000 m (full-duplex)	100 Mbps (200 Mb/s full-duplex mode)	Star(often only point-to-point)
1000Base-SX	Fiber-optic- two strands of multimode 62.5/125 fiber	260m	1Gbps	Star,using buffered distributor hub (or point-to-point)
1000Base-LX	Fiber-optic- two strands of multimode 62.5/125 fiber or monomode fiber	440m (multimode) 5000 m (singlemode)	1Gbps	Star,using buffered distributor hub (or point-to-point)
1000Base-CX	Twinax,150-Ohm-balanced, shielded, specialty cable	25m	1Gbps	Star(or point-to-point)
1000Base-T	Category5	100m	1Gbps	Star

802.5 (token ring)

The IEEE 802.5 Token Ring standards define services for the OSI physical layer and the MAC sublayer of the data link layer. Token Ring computers are situated on a continuous network loop. A Token Ring controls access to the network by passing a token, from one computer to the next. Before they can transmit data they must wait for a free token, thus token passing does not allow two or more computers to begin transmitting at the same time.

·         Token Ring has some major advantages over Ethernet:

·         The maximum frame size for Token Ring is 4k, which is much more efficient that the small Ethernet maximum.

·         Token Ring has long-distance capability.

·         Every station in the ring is guaranteed access to the token at some point; thus, every station can transmit data.

·         Error detection and recovery techniques are also enhanced in a Token Ring environment by using a monitor function normally controlled by a server. For example, if the token is lost or corrupted, the protocol provides a mechanism to generate a new token after a specified time interval has elapsed.

Media	MAC Method	Signal Propagation Method	Speed	Topologies	Maximum Connections
Twisted-pair(various types)	Token passing	Forwarded from device to device (or port to port on a hub) in a closed loop	4Mbps 16 Mbps	Ring Star-using Token Ring repeater hubs	255nodes per segment

802.11b (wireless)

802.11b is a wireless Ethernet technology operating at 11MB. 802.11b devices use Direct Sequence Spread Spectrum (DSSS) radio technology operating in the 2.4GHz frequency band. An 802.11b wireless network consists of wireless NICs and access points. Access points act as wireless hubs to link multiple wireless NICs into a single subnet. Access points also have at least one fixed Ethernet port to allow the wireless network to be bridged to a traditional wired Ethernet network.. Wireless and wired devices can coexist on the same network. 802.11b devices can communicate across a maximum range of 50-300 feet from each other.

FDDI networking technologies

Fiber Distributed Data Interface, shares many of the same features as token ring, such as a token passing, and the continuous network loop configuration. But FDDI has better fault tolerance because of its use of a dual, counter-rotating ring that enables the ring to reconfigure itself in case of a link failure. FDDI also has higher transfer speeds, 100 Mbps for FDDI, compared to 4 - 16 Mbps for Token Ring. Unlike Token Ring, which uses a star topology, FDDI uses a physical ring. Each device in the ring attaches to the adjacent device using a two stranded fiber optic cable. Data travels in one direction on the outer strand and in the other direction on the inner strand. When all devices attached to the dual ring are functioning properly, data travels on only one ring. FDDI transmits data on the second ring only in the event of a link failure.

Media	MAC Method	Signal Propagation Method	Speed	Topologies	Maximum Connections
Fiber-optic	Token passing	Forwardedfrom device to device (or port to port on a hub) in a closed loop	100 Mbps	Double ringStar	500 nodes